Merge series from srinivas.kandagatla@linaro.org:
On Qualcomm Audioreach setup, some of the audio artifacts are seen in
both recording and playback. These patches fix issues by
1. Adjusting the fragment size that dsp can service.
2. schedule available playback buffers in time for dsp to not hit under runs
3. remove some of the manual calculations done to get hardware pointer.
With these patches, am able to see significant Audio quality improvements.
I have few more patches to optimize the dsp drivers, but for now am
keeping this series simple to address the underruns and overruns issues
noticed in pipewire setup.
Any testing would be appreciated.
Please note that on pipewire min-latency has to be set to 512 which
reflects the DSP latency requirements of 10ms. You might see audio
artifacts like glitches if you try to play audio below 256 latency.
The runtime verifier documents that were created were not referenced
in the indices, which caused warning when building the documentation
tree. Those documents are now added to the rv indices.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZ+cRdhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhc3AQCm6C+HJZl28AT7jlFLBwUzgzHJdkQp
hAVp0o6heMjRCwD/QAKUDKaTOeqmmvmP/u2CF/e/IFypBDauwsA3bhiKKA8=
=2HEf
-----END PGP SIGNATURE-----
Merge tag 'trace-latency-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing documentation fix from Steven Rostedt:
"Documentation fix for runtime verifier
The runtime verifier documents that were created were not referenced
in the indices, which caused warning when building the documentation
tree. Those documents are now added to the rv indices"
* tag 'trace-latency-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
Documentation/rv: Add sched pages to the indices
perf record
-----------
* Introduce latency profiling using scheduler information. The latency
profiling is to show impacts on wall-time rather than cpu-time. By
tracking context switches, it can weight samples and find which part
of the code contributed more to the execution latency.
The value (period) of the sample is weighted by dividing it by the
number of parallel execution at the moment. The parallelism is
tracked in perf report with sched-switch records. This will reduce
the portion that are run in parallel and in turn increase the portion
of serial executions.
For now, it's limited to profile processes, IOW system-wide profiling
is not supported. You can add --latency option to enable this.
$ perf record --latency -- make -C tools/perf
I've run the above command for perf build which adds -j option to
make with the number of CPUs in the system internally. Normally
it'd show something like below:
$ perf report -F overhead,comm
...
#
# Overhead Command
# ........ ...............
#
78.97% cc1
6.54% python3
4.21% shellcheck
3.28% ld
1.80% as
1.37% cc1plus
0.80% sh
0.62% clang
0.56% gcc
0.44% perl
0.39% make
...
The cc1 takes around 80% of the overhead as it's the actual compiler.
However it runs in parallel so its contribution to latency may be less
than that. Now, perf report will show both overhead and latency (if
--latency was given at record time) like below:
$ perf report -s comm
...
#
# Overhead Latency Command
# ........ ........ ...............
#
78.97% 48.66% cc1
6.54% 25.68% python3
4.21% 0.39% shellcheck
3.28% 13.70% ld
1.80% 2.56% as
1.37% 3.08% cc1plus
0.80% 0.98% sh
0.62% 0.61% clang
0.56% 0.33% gcc
0.44% 1.71% perl
0.39% 0.83% make
...
You can see latency of cc1 goes down to around 50% and python3 and ld
contribute a lot more than their overhead. You can use --latency
option in perf report to get the same result but ordered by latency.
$ perf report --latency -s comm
perf report
-----------
* As a side effect of the latency profiling work, it adds a new output
field 'latency' and a sort key 'parallelism'. The below is a result
from my system with 64 CPUs. The build was well-parallelized but
contained some serial portions.
$ perf report -s parallelism
...
#
# Overhead Latency Parallelism
# ........ ........ ...........
#
16.95% 1.54% 62
13.38% 1.24% 61
12.50% 70.47% 1
11.81% 1.06% 63
7.59% 0.71% 60
4.33% 12.20% 2
3.41% 0.33% 59
2.05% 0.18% 64
1.75% 1.09% 9
1.64% 1.85% 5
...
* Support Feodra mini-debuginfo which is a LZMA compressed symbol table
inside ".gnu_debugdata" ELF section.
perf annotate
-------------
* Add --code-with-type option to enable data-type profiling with the
usual annotate output. Instead of focusing on data structure, it
shows code annotation together with data type it accesses in case the
instruction refers to a memory location (and it was able to resolve
the target data type). Currently it only works with --stdio.
$ perf annotate --stdio --code-with-type
...
Percent | Source code & Disassembly of vmlinux for cpu/mem-loads,ldlat=30/pp (18 samples, percent: local period)
----------------------------------------------------------------------------------------------------------------------
: 0 0xffffffff81050610 <__fdget>:
0.00 : ffffffff81050610: callq 0xffffffff81c01b80 <__fentry__> # data-type: (stack operation)
0.00 : ffffffff81050615: pushq %rbp # data-type: (stack operation)
0.00 : ffffffff81050616: movq %rsp, %rbp
0.00 : ffffffff81050619: pushq %r15 # data-type: (stack operation)
0.00 : ffffffff8105061b: pushq %r14 # data-type: (stack operation)
0.00 : ffffffff8105061d: pushq %rbx # data-type: (stack operation)
0.00 : ffffffff8105061e: subq $0x10, %rsp
0.00 : ffffffff81050622: movl %edi, %ebx
0.00 : ffffffff81050624: movq %gs:0x7efc4814(%rip), %rax # 0x14e40 <current_task> # data-type: struct task_struct* +0
0.00 : ffffffff8105062c: movq 0x8d0(%rax), %r14 # data-type: struct task_struct +0x8d0 (files)
0.00 : ffffffff81050633: movl (%r14), %eax # data-type: struct files_struct +0 (count.counter)
0.00 : ffffffff81050636: cmpl $0x1, %eax
0.00 : ffffffff81050639: je 0xffffffff810506a9 <__fdget+0x99>
0.00 : ffffffff8105063b: movq 0x20(%r14), %rcx # data-type: struct files_struct +0x20 (fdt)
0.00 : ffffffff8105063f: movl (%rcx), %eax # data-type: struct fdtable +0 (max_fds)
0.00 : ffffffff81050641: cmpl %ebx, %eax
0.00 : ffffffff81050643: jbe 0xffffffff810506ef <__fdget+0xdf>
0.00 : ffffffff81050649: movl %ebx, %r15d
5.56 : ffffffff8105064c: movq 0x8(%rcx), %rdx # data-type: struct fdtable +0x8 (fd)
...
The "# data-type:" part was added with this change. The first few
entries are not very interesting. But later you can it accesses
a couple of fields in the task_struct, files_struct and fdtable.
perf trace
----------
* Support syscall tracing for different ABI. For example it can trace
system calls for 32-bit applications on 64-bit kernel transparently.
* Add --summary-mode=total option to show global syscall summary. The
default is 'thread' to show per-thread syscall summary.
Python support
--------------
* Add more interfaces to 'perf' module to parse events, and config,
enable or disable the event list properly so that it can implement
basic functionalities purely in Python. There is an example code
for these new interfaces in python/tracepoint.py.
* Add mypy and pylint support to enable build time checking. Fix
some code based on the findings from these tools.
Internals
---------
* Introduce io_dir__readdir() API to make directory traveral (usually
for proc or sysfs) efficient with less memory footprint.
JSON vendor events
------------------
* Add events and metrics for ARM Neoverse N3 and V3
* Update events and metrics on various Intel CPUs
* Add/update events for a number of SiFive processors
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSo2x5BnqMqsoHtzsmMstVUGiXMgwUCZ+Y/YQAKCRCMstVUGiXM
g64CAP9sdUgKCe66JilZRAEy9d3Cp835v7KjHSlCXLXkRSoy6wD+KH96Y0OqVtGw
GYON4s9ZoXAoH+J0lKIFSffVL9MhYgY=
=7L7B
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v6.15-2025-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools updates from Namhyung Kim:
"perf record:
- Introduce latency profiling using scheduler information.
The latency profiling is to show impacts on wall-time rather than
cpu-time. By tracking context switches, it can weight samples and
find which part of the code contributed more to the execution
latency.
The value (period) of the sample is weighted by dividing it by the
number of parallel execution at the moment. The parallelism is
tracked in perf report with sched-switch records. This will reduce
the portion that are run in parallel and in turn increase the
portion of serial executions.
For now, it's limited to profile processes, IOW system-wide
profiling is not supported. You can add --latency option to enable
this.
$ perf record --latency -- make -C tools/perf
I've run the above command for perf build which adds -j option to
make with the number of CPUs in the system internally. Normally
it'd show something like below:
$ perf report -F overhead,comm
...
#
# Overhead Command
# ........ ...............
#
78.97% cc1
6.54% python3
4.21% shellcheck
3.28% ld
1.80% as
1.37% cc1plus
0.80% sh
0.62% clang
0.56% gcc
0.44% perl
0.39% make
...
The cc1 takes around 80% of the overhead as it's the actual
compiler. However it runs in parallel so its contribution to
latency may be less than that. Now, perf report will show both
overhead and latency (if --latency was given at record time) like
below:
$ perf report -s comm
...
#
# Overhead Latency Command
# ........ ........ ...............
#
78.97% 48.66% cc1
6.54% 25.68% python3
4.21% 0.39% shellcheck
3.28% 13.70% ld
1.80% 2.56% as
1.37% 3.08% cc1plus
0.80% 0.98% sh
0.62% 0.61% clang
0.56% 0.33% gcc
0.44% 1.71% perl
0.39% 0.83% make
...
You can see latency of cc1 goes down to around 50% and python3 and
ld contribute a lot more than their overhead. You can use --latency
option in perf report to get the same result but ordered by
latency.
$ perf report --latency -s comm
perf report:
- As a side effect of the latency profiling work, it adds a new
output field 'latency' and a sort key 'parallelism'. The below is a
result from my system with 64 CPUs. The build was well-parallelized
but contained some serial portions.
$ perf report -s parallelism
...
#
# Overhead Latency Parallelism
# ........ ........ ...........
#
16.95% 1.54% 62
13.38% 1.24% 61
12.50% 70.47% 1
11.81% 1.06% 63
7.59% 0.71% 60
4.33% 12.20% 2
3.41% 0.33% 59
2.05% 0.18% 64
1.75% 1.09% 9
1.64% 1.85% 5
...
- Support Feodra mini-debuginfo which is a LZMA compressed symbol
table inside ".gnu_debugdata" ELF section.
perf annotate:
- Add --code-with-type option to enable data-type profiling with the
usual annotate output.
Instead of focusing on data structure, it shows code annotation
together with data type it accesses in case the instruction refers
to a memory location (and it was able to resolve the target data
type). Currently it only works with --stdio.
$ perf annotate --stdio --code-with-type
...
Percent | Source code & Disassembly of vmlinux for cpu/mem-loads,ldlat=30/pp (18 samples, percent: local period)
----------------------------------------------------------------------------------------------------------------------
: 0 0xffffffff81050610 <__fdget>:
0.00 : ffffffff81050610: callq 0xffffffff81c01b80 <__fentry__> # data-type: (stack operation)
0.00 : ffffffff81050615: pushq %rbp # data-type: (stack operation)
0.00 : ffffffff81050616: movq %rsp, %rbp
0.00 : ffffffff81050619: pushq %r15 # data-type: (stack operation)
0.00 : ffffffff8105061b: pushq %r14 # data-type: (stack operation)
0.00 : ffffffff8105061d: pushq %rbx # data-type: (stack operation)
0.00 : ffffffff8105061e: subq $0x10, %rsp
0.00 : ffffffff81050622: movl %edi, %ebx
0.00 : ffffffff81050624: movq %gs:0x7efc4814(%rip), %rax # 0x14e40 <current_task> # data-type: struct task_struct* +0
0.00 : ffffffff8105062c: movq 0x8d0(%rax), %r14 # data-type: struct task_struct +0x8d0 (files)
0.00 : ffffffff81050633: movl (%r14), %eax # data-type: struct files_struct +0 (count.counter)
0.00 : ffffffff81050636: cmpl $0x1, %eax
0.00 : ffffffff81050639: je 0xffffffff810506a9 <__fdget+0x99>
0.00 : ffffffff8105063b: movq 0x20(%r14), %rcx # data-type: struct files_struct +0x20 (fdt)
0.00 : ffffffff8105063f: movl (%rcx), %eax # data-type: struct fdtable +0 (max_fds)
0.00 : ffffffff81050641: cmpl %ebx, %eax
0.00 : ffffffff81050643: jbe 0xffffffff810506ef <__fdget+0xdf>
0.00 : ffffffff81050649: movl %ebx, %r15d
5.56 : ffffffff8105064c: movq 0x8(%rcx), %rdx # data-type: struct fdtable +0x8 (fd)
...
The "# data-type:" part was added with this change. The first few
entries are not very interesting. But later you can it accesses a
couple of fields in the task_struct, files_struct and fdtable.
perf trace:
- Support syscall tracing for different ABI. For example it can trace
system calls for 32-bit applications on 64-bit kernel
transparently.
- Add --summary-mode=total option to show global syscall summary. The
default is 'thread' to show per-thread syscall summary.
Python support:
- Add more interfaces to 'perf' module to parse events, and config,
enable or disable the event list properly so that it can implement
basic functionalities purely in Python. There is an example code
for these new interfaces in python/tracepoint.py.
- Add mypy and pylint support to enable build time checking. Fix some
code based on the findings from these tools.
Internals:
- Introduce io_dir__readdir() API to make directory traveral (usually
for proc or sysfs) efficient with less memory footprint.
JSON vendor events:
- Add events and metrics for ARM Neoverse N3 and V3
- Update events and metrics on various Intel CPUs
- Add/update events for a number of SiFive processors"
* tag 'perf-tools-for-v6.15-2025-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: (229 commits)
perf bpf-filter: Fix a parsing error with comma
perf report: Fix a memory leak for perf_env on AMD
perf trace: Fix wrong size to bpf_map__update_elem call
perf tools: annotate asm_pure_loop.S
perf python: Fix setup.py mypy errors
perf test: Address attr.py mypy error
perf build: Add pylint build tests
perf build: Add mypy build tests
perf build: Rename TEST_LOGS to SHELL_TEST_LOGS
tools/build: Don't pass test log files to linker
perf bench sched pipe: fix enforced blocking reads in worker_thread
perf tools: Fix is_compat_mode build break in ppc64
perf build: filter all combinations of -flto for libperl
perf vendor events arm64 AmpereOneX: Fix frontend_bound calculation
perf vendor events arm64: AmpereOne/AmpereOneX: Mark LD_RETIRED impacted by errata
perf trace: Fix evlist memory leak
perf trace: Fix BTF memory leak
perf trace: Make syscall table stable
perf syscalltbl: Mask off ABI type for MIPS system calls
perf build: Remove Makefile.syscalls
...
Should an error occur after a successful regulator_bulk_enable() call,
regulator_bulk_disable() should be called, as already done in the remove
function.
Instead of adding an error handling path in the probe, switch from
devm_regulator_bulk_get() to devm_regulator_bulk_get_enable() and
simplify the remove function and some other places accordingly.
Finally, add a missing const when defining rt5665_supply_names to please
checkpatch and constify a few bytes.
Fixes: 33ada14a26c8 ("ASoC: add rt5665 codec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/e3c2aa1b2fdfa646752d94f4af968630c0d58248.1742629525.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
The _DDC method should return a buffer, or an integer in case of an error.
But some Lenovo laptops incorrectly return EDID as buffer in ACPI package.
Calling _DDC generates this ACPI Warning:
ACPI Warning: \_SB.PCI0.GP17.VGA.LCD._DDC: Return type mismatch - \
found Package, expected Integer/Buffer (20240827/nspredef-254)
Use the first element of the package to get the EDID buffer.
The DSDT:
Name (AUOP, Package (0x01)
{
Buffer (0x80)
{
...
}
})
...
Method (_DDC, 1, NotSerialized) // _DDC: Display Data Current
{
If ((PAID == AUID))
{
Return (AUOP) /* \_SB_.PCI0.GP17.VGA_.LCD_.AUOP */
}
ElseIf ((PAID == IVID))
{
Return (IVOP) /* \_SB_.PCI0.GP17.VGA_.LCD_.IVOP */
}
ElseIf ((PAID == BOID))
{
Return (BOEP) /* \_SB_.PCI0.GP17.VGA_.LCD_.BOEP */
}
ElseIf ((PAID == SAID))
{
Return (SUNG) /* \_SB_.PCI0.GP17.VGA_.LCD_.SUNG */
}
Return (Zero)
}
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/Apx_B_Video_Extensions/output-device-specific-methods.html#ddc-return-the-edid-for-this-device
Cc: stable@vger.kernel.org
Fixes: c6a837088bed ("drm/amd/display: Fetch the EDID from _DDC if available for eDP")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4085
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/61c3df83ab73aba0bc7a941a443cd7faf4cf7fb0.1743195250.git.soyer@irl.hu
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the existing code, the buffer position is only reset in pointer
callback, which leaves the possiblity of it going over the size of
buffer size and reporting incorrect position to userspace.
Without this patch, its possible to see errors like:
snd-x1e80100 sound: invalid position: pcmC0D0p:0, pos = 12288, buffer size = 12288, period size = 1536
snd-x1e80100 sound: invalid position: pcmC0D0p:0, pos = 12288, buffer size = 12288, period size = 1536
Fixes: 9b4fe0f1cd791 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250314174800.10142-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Period sizes less than 6k for capture path triggers overruns in the
dsp capture pipeline.
Change the period size and number of periods to value which DSP is happy with.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250314174800.10142-6-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects the periods to be aligned to fragment sizes, currently
setting up to hw constriants on periods bytes is not going to work
correctly as we can endup with periods sizes aligned to 32 bytes however
not aligned to fragment size.
Update the constriants to use fragment size, and also set at step of
10ms for period size to accommodate DSP requirements of 10ms latency.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250314174800.10142-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement an helper function in q6apm to be able to read the current
hardware pointer for both read and write buffers.
This should help q6apm-dai to get the hardware pointer consistently
without it doing manual calculation, which could go wrong in some race
conditions.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250314174800.10142-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
With the existing code, we are only setting up one period at a time, in a
ping-pong buffer style. This triggers lot of underruns in the dsp
leading to jitter noise during audio playback.
Fix this by scheduling all available periods, this will ensure that the dsp
has enough buffer feed and ultimatley fixing the underruns and audio
distortion.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Cc: stable@vger.kernel.org
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250314174800.10142-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A previous commit removed the use of this footnote, delete it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 3fdf2ec7da1c ("Documentation: ublk: Drop Stefan Hajnoczi's message footnote")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the ring is allocated, it is kzalloc-ed. ring->queue_refs will
already be initialized to 0 by default. It does not need to be
atomically set to 0.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
There is a race condition leading to a kernel crash from a null
dereference when attemping to access fc->lock in
fuse_uring_create_queue(). fc may be NULL in the case where another
thread is creating the uring in fuse_uring_create() and has set
fc->ring but has not yet set ring->fc when fuse_uring_create_queue()
reads ring->fc. There is another race condition as well where in
fuse_uring_register(), ring->nr_queues may still be 0 and not yet set
to the new value when we compare qid against it.
This fix sets fc->ring only after ring->fc and ring->nr_queues have been
set, which guarantees now that ring->fc is a proper pointer when any
queues are created and ring->nr_queues reflects the right number of
queues if ring is not NULL. We must use smp_store_release() and
smp_load_acquire() semantics to ensure the ordering will remain correct
where fc->ring is assigned only after ring->fc and ring->nr_queues have
been assigned.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Fixes: 24fe962c86f5 ("fuse: {io-uring} Handle SQEs - register commands")
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Our file system has a translation capability for S3-to-posix.
The current value of 1kiB is enough to cover S3 keys, but
does not allow encoding of %xx escape characters.
The limit is increased to (PATH_MAX - 1), as we need
3 x 1024 and that is close to PATH_MAX (4kB) already.
-1 is used as the terminating null is not included in the
length calculation.
Testing large file names was hard with libfuse/example file systems,
so I created a new memfs that does not have a 255 file name length
limitation.
https://github.com/libfuse/libfuse/pull/1077
The connection is initialized with FUSE_NAME_LOW_MAX, which
is set to the previous value of FUSE_NAME_MAX of 1024. With
FUSE_MIN_READ_BUFFER of 8192 that is enough for two file names
+ fuse headers.
When FUSE_INIT reply sets max_pages to a value > 1 we know
that fuse daemon supports request buffers of at least 2 pages
(+ header) and can therefore hold 2 x PATH_MAX file names - operations
like rename or link that need two file names are no issue then.
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
fuse_notify_inval_entry and fuse_notify_delete were using fixed allocations
of FUSE_NAME_MAX to hold the file name. Often that large buffers are not
needed as file names might be smaller, so this uses the actual file name
size to do the allocation.
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Introduce two new sysctls, "default_request_timeout" and
"max_request_timeout". These control how long (in seconds) a server can
take to reply to a request. If the server does not reply by the timeout,
then the connection will be aborted. The upper bound on these sysctl
values is 65535.
"default_request_timeout" sets the default timeout if no timeout is
specified by the fuse server on mount. 0 (default) indicates no default
timeout should be enforced. If the server did specify a timeout, then
default_request_timeout will be ignored.
"max_request_timeout" sets the max amount of time the server may take to
reply to a request. 0 (default) indicates no maximum timeout. If
max_request_timeout is set and the fuse server attempts to set a
timeout greater than max_request_timeout, the system will use
max_request_timeout as the timeout. Similarly, if default_request_timeout
is greater than max_request_timeout, the system will use
max_request_timeout as the timeout. If the server does not request a
timeout and default_request_timeout is set to 0 but max_request_timeout
is set, then the timeout will be max_request_timeout.
Please note that these timeouts are not 100% precise. The request may
take roughly an extra FUSE_TIMEOUT_TIMER_FREQ seconds beyond the set max
timeout due to how it's internally implemented.
$ sysctl -a | grep fuse.default_request_timeout
fs.fuse.default_request_timeout = 0
$ echo 65536 | sudo tee /proc/sys/fs/fuse/default_request_timeout
tee: /proc/sys/fs/fuse/default_request_timeout: Invalid argument
$ echo 65535 | sudo tee /proc/sys/fs/fuse/default_request_timeout
65535
$ sysctl -a | grep fuse.default_request_timeout
fs.fuse.default_request_timeout = 65535
$ echo 0 | sudo tee /proc/sys/fs/fuse/default_request_timeout
0
$ sysctl -a | grep fuse.default_request_timeout
fs.fuse.default_request_timeout = 0
[Luis Henriques: Limit the timeout to the range [FUSE_TIMEOUT_TIMER_FREQ,
fuse_max_req_timeout]]
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Luis Henriques <luis@igalia.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
There are situations where fuse servers can become unresponsive or
stuck, for example if the server is deadlocked. Currently, there's no
good way to detect if a server is stuck and needs to be killed manually.
This commit adds an option for enforcing a timeout (in seconds) for
requests where if the timeout elapses without the server responding to
the request, the connection will be automatically aborted.
Please note that these timeouts are not 100% precise. For example, the
request may take roughly an extra FUSE_TIMEOUT_TIMER_FREQ seconds beyond
the requested timeout due to internal implementation, in order to
mitigate overhead.
[SzM: Bump the API version number]
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
If filesystem doesn't support FUSE_LINK (i.e. returns -ENOSYS), then
remember this and next time return immediately, without incurring the
overhead of a round trip to the server.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
link() is documented to return EPERM when a filesystem doesn't support
the operation, return that instead.
Link: https://github.com/libfuse/libfuse/issues/925
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Function fuse_uring_create() is used only from dev_uring.c and does not
need to be exposed in the header file. Furthermore, it has the wrong
signature.
While there, also remove the 'struct fuse_ring' forward declaration.
Signed-off-by: Luis Henriques <luis@igalia.com>
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
task-A (application) might be in request_wait_answer and
try to remove the request when it has FR_PENDING set.
task-B (a fuse-server io-uring task) might handle this
request with FUSE_IO_URING_CMD_COMMIT_AND_FETCH, when
fetching the next request and accessed the req from
the pending list in fuse_uring_ent_assign_req().
That code path was not protected by fiq->lock and so
might race with task-A.
For scaling reasons we better don't use fiq->lock, but
add a handler to remove canceled requests from the queue.
This also removes usage of fiq->lock from
fuse_uring_add_req_to_ring_ent() altogether, as it was
there just to protect against this race and incomplete.
Also added is a comment why FR_PENDING is not cleared.
Fixes: c090c8abae4b ("fuse: Add io-uring sqe commit and fetch support")
Cc: <stable@vger.kernel.org> # v6.14
Reported-by: Joanne Koong <joannelkoong@gmail.com>
Closes: https://lore.kernel.org/all/CAJnrk1ZgHNb78dz-yfNTpxmW7wtT88A=m-zF0ZoLXKLUHRjNTw@mail.gmail.com/
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Correct detect condition is applied to the entire 5221 family of PHYs.
Fixes: 3abbd0699b67 ("net: phy: broadcom: add support for BCM5221 phy")
Signed-off-by: Jim Liu <jim.t90615@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit 496121c02127 ("ACPI: processor: idle: Allow probing on
platforms with one ACPI C-state"), the acpi_idle driver wouldn't load on
systems without a valid C-State at least as deep as C2.
The behavior was desirable for guests on hypervisors such as VMWare
ESXi, which by default don't have the _CST ACPI method, and set the C2
and C3 latencies to 101 and 1001 microseconds respectively via the FADT,
to signify they're unsupported.
Since the above change though, these virtualized deployments end up
loading acpi_idle, and thus entering the default C1 C-State set by
acpi_processor_get_power_info_default(); this is undesirable for a
system that's communicating to the OS it doesn't want C-States (missing
_CST, and invalid C2/C3 in FADT).
Make acpi_processor_get_power_info_fadt() return -ENODEV in that case,
so that acpi_processor_get_cstate_info() exits early and doesn't set
pr->flags.power = 1.
Fixes: 496121c02127 ("ACPI: processor: idle: Allow probing on platforms with one ACPI C-state")
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Link: https://patch.msgid.link/20250328143040.9348-1-ggherdovich@suse.cz
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IPC message cannot be sent from the irq thread directly as the message will
not receive the reply (interrupts are disabled) and it will time out - the
reply is going to be received right after the we leave the irq thread.
This is a different case compared to the delayed IPC messages due to DSP
busy state.
Add support for sending the mic privacy change notification to the firmware
from a work instead of the process callback.
The work needs to be canceled if there is a chance that it might be running
on module remove or before system/runtime suspend.
Fixes: 4a43c3241ec3 ("ASoC: SOF: Intel: ptl: Add support for mic privacy")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20250331070623.5985-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The I3C master driver may receive an IBI from a target device that has not
been probed yet. In such cases, the master calls `i3c_master_queue_ibi()`
to queue an IBI work task, leading to "Unable to handle kernel read from
unreadable memory" and resulting in a kernel panic.
Typical IBI handling flow:
1. The I3C master scans target devices and probes their respective drivers.
2. The target device driver calls `i3c_device_request_ibi()` to enable IBI
and assigns `dev->ibi = ibi`.
3. The I3C master receives an IBI from the target device and calls
`i3c_master_queue_ibi()` to queue the target device driver’s IBI
handler task.
However, since target device events are asynchronous to the I3C probe
sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`,
leading to a kernel panic.
Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing
an uninitialized `dev->ibi`, ensuring stability.
Fixes: 3a379bbcea0af ("i3c: Add core I3C infrastructure")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/Z9gjGYudiYyl3bSe@lizhi-Precision-Tower-5810/
Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250326123047.2797946-1-manjunatha.venkatesh@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
OF APIs are usually NULL-aware and returns an error in case when
device node is not present or supported. We already have a check
for the returned value, no need to check for the parameter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250321193044.457649-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The fwnode.h is not supposed to be used by the drivers as it
has the definitions for the core parts for different device
property provider implementations. Drop it.
Note, that fwnode API for drivers is provided in property.h
which is included here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250331070758.3986134-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because of different crate names ("pin-init" and "pin_init") passed to
"append_crate" and "append_crate_with_generated", the script fails with
"KeyError: 'pin-init'".
To overcome the issue, pass the same name to both functions.
Signed-off-by: Andrei Lalaev <andrei.lalaev@anton-paar.com>
Link: https://lore.kernel.org/r/AM9PR03MB7074692E5D24C288D2BBC801C8AD2@AM9PR03MB7074.eurprd03.prod.outlook.com
Fixes: 4e82c87058f4 ("Merge tag 'rust-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux")
[ Made author match the Signed-off-by one. Added newline. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
This patch adds the HP OMEN 16 Laptop xd000xx to enable mute led.
it uses ALC245_FIXUP_HP_MUTE_LED_COEFBIT with a slight modification
setting mute_led_coef.off to 0(it was set to 4 i guess
in that function) which i referred to your previous patch disscusion
https://bugzilla.kernel.org/show_bug.cgi?id=214735 .
i am not sure whether i can modify the current working function so i
added another version calling
ALC245_FIXUP_HP_MUTE_LED_V1_COEFBIT. and both works for me.
Tested on 6.13.4-arch1-1 to 6.14.0-arch1-1
Signed-off-by: Sharan Kumar M <sharweshraajan@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20250329154105.7618-2-sharweshraajan@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toolchain and infrastructure:
- Extract the 'pin-init' API from the 'kernel' crate and make it into
a standalone crate.
In order to do this, the contents are rearranged so that they can
easily be kept in sync with the version maintained out-of-tree that
other projects have started to use too (or plan to, like QEMU).
This will reduce the maintenance burden for Benno, who will now have
his own sub-tree, and will simplify future expected changes like the
move to use 'syn' to simplify the implementation.
- Add '#[test]'-like support based on KUnit.
We already had doctests support based on KUnit, which takes the
examples in our Rust documentation and runs them under KUnit.
Now, we are adding the beginning of the support for "normal" tests,
similar to those the '#[test]' tests in userspace Rust. For instance:
#[kunit_tests(my_suite)]
mod tests {
#[test]
fn my_test() {
assert_eq!(1 + 1, 2);
}
}
Unlike with doctests, the 'assert*!'s do not map to the KUnit
assertion APIs yet.
- Check Rust signatures at compile time for functions called from C by
name.
In particular, introduce a new '#[export]' macro that can be placed
in the Rust function definition. It will ensure that the function
declaration on the C side matches the signature on the Rust function:
#[export]
pub unsafe extern "C" fn my_function(a: u8, b: i32) -> usize {
// ...
}
The macro essentially forces the compiler to compare the types of
the actual Rust function and the 'bindgen'-processed C signature.
These cases are rare so far. In the future, we may consider
introducing another tool, 'cbindgen', to generate C headers
automatically. Even then, having these functions explicitly marked
may be a good idea anyway.
- Enable the 'raw_ref_op' Rust feature: it is already stable, and
allows us to use the new '&raw' syntax, avoiding a couple macros.
After everyone has migrated, we will disallow the macros.
- Pass the correct target to 'bindgen' on Usermode Linux.
- Fix 'rusttest' build in macOS.
'kernel' crate:
- New 'hrtimer' module: add support for setting up intrusive timers
without allocating when starting the timer. Add support for
'Pin<Box<_>>', 'Arc<_>', 'Pin<&_>' and 'Pin<&mut _>' as pointer types
for use with timer callbacks. Add support for setting clock source
and timer mode.
- New 'dma' module: add a simple DMA coherent allocator abstraction and
a test sample driver.
- 'list' module: make the linked list 'Cursor' point between elements,
rather than at an element, which is more convenient to us and allows
for cursors to empty lists; and document it with examples of how to
perform common operations with the provided methods.
- 'str' module: implement a few traits for 'BStr' as well as the
'strip_prefix()' method.
- 'sync' module: add 'Arc::as_ptr'.
- 'alloc' module: add 'Box::into_pin'.
- 'error' module: extend the 'Result' documentation, including a few
examples on different ways of handling errors, a warning about using
methods that may panic, and links to external documentation.
'macros' crate:
- 'module' macro: add the 'authors' key to support multiple authors.
The original key will be kept until everyone has migrated.
Documentation:
- Add error handling sections.
MAINTAINERS:
- Add Danilo Krummrich as reviewer of the Rust "subsystem".
- Add 'RUST [PIN-INIT]' entry with Benno Lossin as maintainer. It has
its own sub-tree.
- Add sub-tree for 'RUST [ALLOC]'.
- Add 'DMA MAPPING HELPERS DEVICE DRIVER API [RUST]' entry with Abdiel
Janulgue as primary maintainer. It will go through the sub-tree of
the 'RUST [ALLOC]' entry.
- Add 'HIGH-RESOLUTION TIMERS [RUST]' entry with Andreas Hindborg as
maintainer. It has its own sub-tree.
And a few other cleanups and improvements.
-----BEGIN PGP SIGNATURE-----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=PCxf
-----END PGP SIGNATURE-----
Merge tag 'rust-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull Rust updates from Miguel Ojeda:
"Toolchain and infrastructure:
- Extract the 'pin-init' API from the 'kernel' crate and make it into
a standalone crate.
In order to do this, the contents are rearranged so that they can
easily be kept in sync with the version maintained out-of-tree that
other projects have started to use too (or plan to, like QEMU).
This will reduce the maintenance burden for Benno, who will now
have his own sub-tree, and will simplify future expected changes
like the move to use 'syn' to simplify the implementation.
- Add '#[test]'-like support based on KUnit.
We already had doctests support based on KUnit, which takes the
examples in our Rust documentation and runs them under KUnit.
Now, we are adding the beginning of the support for "normal" tests,
similar to those the '#[test]' tests in userspace Rust. For
instance:
#[kunit_tests(my_suite)]
mod tests {
#[test]
fn my_test() {
assert_eq!(1 + 1, 2);
}
}
Unlike with doctests, the 'assert*!'s do not map to the KUnit
assertion APIs yet.
- Check Rust signatures at compile time for functions called from C
by name.
In particular, introduce a new '#[export]' macro that can be placed
in the Rust function definition. It will ensure that the function
declaration on the C side matches the signature on the Rust
function:
#[export]
pub unsafe extern "C" fn my_function(a: u8, b: i32) -> usize {
// ...
}
The macro essentially forces the compiler to compare the types of
the actual Rust function and the 'bindgen'-processed C signature.
These cases are rare so far. In the future, we may consider
introducing another tool, 'cbindgen', to generate C headers
automatically. Even then, having these functions explicitly marked
may be a good idea anyway.
- Enable the 'raw_ref_op' Rust feature: it is already stable, and
allows us to use the new '&raw' syntax, avoiding a couple macros.
After everyone has migrated, we will disallow the macros.
- Pass the correct target to 'bindgen' on Usermode Linux.
- Fix 'rusttest' build in macOS.
'kernel' crate:
- New 'hrtimer' module: add support for setting up intrusive timers
without allocating when starting the timer. Add support for
'Pin<Box<_>>', 'Arc<_>', 'Pin<&_>' and 'Pin<&mut _>' as pointer
types for use with timer callbacks. Add support for setting clock
source and timer mode.
- New 'dma' module: add a simple DMA coherent allocator abstraction
and a test sample driver.
- 'list' module: make the linked list 'Cursor' point between
elements, rather than at an element, which is more convenient to us
and allows for cursors to empty lists; and document it with
examples of how to perform common operations with the provided
methods.
- 'str' module: implement a few traits for 'BStr' as well as the
'strip_prefix()' method.
- 'sync' module: add 'Arc::as_ptr'.
- 'alloc' module: add 'Box::into_pin'.
- 'error' module: extend the 'Result' documentation, including a few
examples on different ways of handling errors, a warning about
using methods that may panic, and links to external documentation.
'macros' crate:
- 'module' macro: add the 'authors' key to support multiple authors.
The original key will be kept until everyone has migrated.
Documentation:
- Add error handling sections.
MAINTAINERS:
- Add Danilo Krummrich as reviewer of the Rust "subsystem".
- Add 'RUST [PIN-INIT]' entry with Benno Lossin as maintainer. It has
its own sub-tree.
- Add sub-tree for 'RUST [ALLOC]'.
- Add 'DMA MAPPING HELPERS DEVICE DRIVER API [RUST]' entry with
Abdiel Janulgue as primary maintainer. It will go through the
sub-tree of the 'RUST [ALLOC]' entry.
- Add 'HIGH-RESOLUTION TIMERS [RUST]' entry with Andreas Hindborg as
maintainer. It has its own sub-tree.
And a few other cleanups and improvements"
* tag 'rust-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux: (71 commits)
rust: dma: add `Send` implementation for `CoherentAllocation`
rust: macros: fix `make rusttest` build on macOS
rust: block: refactor to use `&raw mut`
rust: enable `raw_ref_op` feature
rust: uaccess: name the correct function
rust: rbtree: fix comments referring to Box instead of KBox
rust: hrtimer: add maintainer entry
rust: hrtimer: add clocksource selection through `ClockId`
rust: hrtimer: add `HrTimerMode`
rust: hrtimer: implement `HrTimerPointer` for `Pin<Box<T>>`
rust: alloc: add `Box::into_pin`
rust: hrtimer: implement `UnsafeHrTimerPointer` for `Pin<&mut T>`
rust: hrtimer: implement `UnsafeHrTimerPointer` for `Pin<&T>`
rust: hrtimer: add `hrtimer::ScopedHrTimerPointer`
rust: hrtimer: add `UnsafeHrTimerPointer`
rust: hrtimer: allow timer restart from timer handler
rust: str: implement `strip_prefix` for `BStr`
rust: str: implement `AsRef<BStr>` for `[u8]` and `BStr`
rust: str: implement `Index` for `BStr`
rust: str: implement `PartialEq` for `BStr`
...
- Use RCU instead of RCU-sched
The mix of rcu_read_lock(), rcu_read_lock_sched() and preempt_disable()
in the module code and its users has been replaced with just
rcu_read_lock().
- The rest of changes are smaller fixes and updates.
The changes have been on linux-next for at least 2 weeks, with the RCU
cleanup present for 2 months. One performance problem was reported with the
RCU change when KASAN + lockdep were enabled, but it was effectively
addressed by the already merged ee57ab5a3212 ("locking/lockdep: Disable
KASAN instrumentation of lockdep.c").
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEIduBR9MnFA82q/jtumpXJwqY6poFAmfmwrsUHHBldHIucGF2
bHVAc3VzZS5jb20ACgkQumpXJwqY6prWxgf/S7Pvdywm10vJ6fooYa+GxXNMwhyh
XRjZ4m9gjeTNf2KLwX0XHv0XZeFHOmHfjd3iI+pS6CXZnCFTN9J3XPLYsrTxXUb6
U6zzLf8Zsz8TzeI4dgvSBsZln7oICSACkAgdJCq23hpNKeaeRo91dgiZaIwyZJG3
FekqSFtP7pYhfFoNkrFKysqbgl1+RWWZ79L2qRJA0bPzVFlvRUuh6cOHQw+8RMqf
BYLwnArjTkW8AcXpxIXSiwphDHVZ81B96xoplavyoprA5FDpv1W+8y4DtxdWFn+1
QVWCs/ZV3KrwXWpZev625w3fIOOIXILqRINOzLfvXTw+1xFS3TzSQEpVeg==
=4OKc
-----END PGP SIGNATURE-----
Merge tag 'modules-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux
Pull modules updates from Petr Pavlu:
- Use RCU instead of RCU-sched
The mix of rcu_read_lock(), rcu_read_lock_sched() and
preempt_disable() in the module code and its users has
been replaced with just rcu_read_lock()
- The rest of changes are smaller fixes and updates
* tag 'modules-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux: (32 commits)
MAINTAINERS: Update the MODULE SUPPORT section
module: Remove unnecessary size argument when calling strscpy()
module: Replace deprecated strncpy() with strscpy()
params: Annotate struct module_param_attrs with __counted_by()
bug: Use RCU instead RCU-sched to protect module_bug_list.
static_call: Use RCU in all users of __module_text_address().
kprobes: Use RCU in all users of __module_text_address().
bpf: Use RCU in all users of __module_text_address().
jump_label: Use RCU in all users of __module_text_address().
jump_label: Use RCU in all users of __module_address().
x86: Use RCU in all users of __module_address().
cfi: Use RCU while invoking __module_address().
powerpc/ftrace: Use RCU in all users of __module_text_address().
LoongArch: ftrace: Use RCU in all users of __module_text_address().
LoongArch/orc: Use RCU in all users of __module_address().
arm64: module: Use RCU in all users of __module_text_address().
ARM: module: Use RCU in all users of __module_text_address().
module: Use RCU in all users of __module_text_address().
module: Use RCU in all users of __module_address().
module: Use RCU in search_module_extables().
...
- Fix a large number of x86 Kconfig dependency and help text accuracy
bugs/problems, by Mateusz Jończyk and David Heideberg.
- Fix a VM_PAT interaction with fork() crash. This also touches
core kernel code.
- Fix an ORC unwinder bug for interrupt entries
- Fixes and cleanups.
- Fix an AMD microcode loader bug that can promote verification failures
into success.
- Add early-printk support for MMIO based UARTs on an x86 board that
had no other serial debugging facility and also experienced early
boot crashes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/qKX
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2025-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes and updates from Ingo Molnar:
- Fix a large number of x86 Kconfig dependency and help text accuracy
bugs/problems, by Mateusz Jończyk and David Heideberg
- Fix a VM_PAT interaction with fork() crash. This also touches core
kernel code
- Fix an ORC unwinder bug for interrupt entries
- Fixes and cleanups
- Fix an AMD microcode loader bug that can promote verification
failures into success
- Add early-printk support for MMIO based UARTs on an x86 board that
had no other serial debugging facility and also experienced early
boot crashes
* tag 'x86-urgent-2025-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix __apply_microcode_amd()'s return value
x86/mm/pat: Fix VM_PAT handling when fork() fails in copy_page_range()
x86/fpu: Update the outdated comment above fpstate_init_user()
x86/early_printk: Add support for MMIO-based UARTs
x86/dumpstack: Fix inaccurate unwinding from exception stacks due to misplaced assignment
x86/entry: Fix ORC unwinder for PUSH_REGS with save_ret=1
x86/Kconfig: Fix lists in X86_EXTENDED_PLATFORM help text
x86/Kconfig: Correct X86_X2APIC help text
x86/speculation: Remove the extra #ifdef around CALL_NOSPEC
x86/Kconfig: Document release year of glibc 2.3.3
x86/Kconfig: Make CONFIG_PCI_CNB20LE_QUIRK depend on X86_32
x86/Kconfig: Document CONFIG_PCI_MMCONFIG
x86/Kconfig: Update lists in X86_EXTENDED_PLATFORM
x86/Kconfig: Move all X86_EXTENDED_PLATFORM options together
x86/Kconfig: Always enable ARCH_SPARSEMEM_ENABLE
x86/Kconfig: Enable X86_X2APIC by default and improve help text
There's something going on with the data move path; log the original key
being moved for debugging.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Add a journal entry type for logging - but logging a bkey, not a string;
to be used for data move path debugging.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
-----BEGIN PGP SIGNATURE-----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=AHTr
-----END PGP SIGNATURE-----
Merge tag 'bpf_try_alloc_pages' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf try_alloc_pages() support from Alexei Starovoitov:
"The pull includes work from Sebastian, Vlastimil and myself with a lot
of help from Michal and Shakeel.
This is a first step towards making kmalloc reentrant to get rid of
slab wrappers: bpf_mem_alloc, kretprobe's objpool, etc. These patches
make page allocator safe from any context.
Vlastimil kicked off this effort at LSFMM 2024:
https://lwn.net/Articles/974138/
and we continued at LSFMM 2025:
https://lore.kernel.org/all/CAADnVQKfkGxudNUkcPJgwe3nTZ=xohnRshx9kLZBTmR_E1DFEg@mail.gmail.com/
Why:
SLAB wrappers bind memory to a particular subsystem making it
unavailable to the rest of the kernel. Some BPF maps in production
consume Gbytes of preallocated memory. Top 5 in Meta: 1.5G, 1.2G,
1.1G, 300M, 200M. Once we have kmalloc that works in any context BPF
map preallocation won't be necessary.
How:
Synchronous kmalloc/page alloc stack has multiple stages going from
fast to slow: cmpxchg16 -> slab_alloc -> new_slab -> alloc_pages ->
rmqueue_pcplist -> __rmqueue, where rmqueue_pcplist was already
relying on trylock.
This set changes rmqueue_bulk/rmqueue_buddy to attempt a trylock and
return ENOMEM if alloc_flags & ALLOC_TRYLOCK. It then wraps this
functionality into try_alloc_pages() helper. We make sure that the
logic is sane in PREEMPT_RT.
End result: try_alloc_pages()/free_pages_nolock() are safe to call
from any context.
try_kmalloc() for any context with similar trylock approach will
follow. It will use try_alloc_pages() when slab needs a new page.
Though such try_kmalloc/page_alloc() is an opportunistic allocator,
this design ensures that the probability of successful allocation of
small objects (up to one page in size) is high.
Even before we have try_kmalloc(), we already use try_alloc_pages() in
BPF arena implementation and it's going to be used more extensively in
BPF"
* tag 'bpf_try_alloc_pages' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
mm: Fix the flipped condition in gfpflags_allow_spinning()
bpf: Use try_alloc_pages() to allocate pages for bpf needs.
mm, bpf: Use memcg in try_alloc_pages().
memcg: Use trylock to access memcg stock_lock.
mm, bpf: Introduce free_pages_nolock()
mm, bpf: Introduce try_alloc_pages() for opportunistic page allocation
locking/local_lock: Introduce localtry_lock_t
Not all compilers fully initialize these - they're not guaranteed to
because of the union shenanigans.
Fixes: https://github.com/koverstreet/bcachefs/issues/844
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
We don't care about errors from asynchronous ops that were because we
did an emergency shutdown; silence them.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
bch2_evict_subvolume_inodes() was getting stuck - due to incorrectly
pruning the dcache.
Also, fix missing permissions checks.
Reported-by: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
-----BEGIN PGP SIGNATURE-----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=5O7h
-----END PGP SIGNATURE-----
Merge tag 'bpf_res_spin_lock' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf relisient spinlock support from Alexei Starovoitov:
"This patch set introduces Resilient Queued Spin Lock (or rqspinlock
with res_spin_lock() and res_spin_unlock() APIs).
This is a qspinlock variant which recovers the kernel from a stalled
state when the lock acquisition path cannot make forward progress.
This can occur when a lock acquisition attempt enters a deadlock
situation (e.g. AA, or ABBA), or more generally, when the owner of the
lock (which we’re trying to acquire) isn’t making forward progress.
Deadlock detection is the main mechanism used to provide instant
recovery, with the timeout mechanism acting as a final line of
defense. Detection is triggered immediately when beginning the waiting
loop of a lock slow path.
Additionally, BPF programs attached to different parts of the kernel
can introduce new control flow into the kernel, which increases the
likelihood of deadlocks in code not written to handle reentrancy.
There have been multiple syzbot reports surfacing deadlocks in
internal kernel code due to the diverse ways in which BPF programs can
be attached to different parts of the kernel. By switching the BPF
subsystem’s lock usage to rqspinlock, all of these issues are
mitigated at runtime.
This spin lock implementation allows BPF maps to become safer and
remove mechanisms that have fallen short in assuring safety when
nesting programs in arbitrary ways in the same context or across
different contexts.
We run benchmarks that stress locking scalability and perform
comparison against the baseline (qspinlock). For the rqspinlock case,
we replace the default qspinlock with it in the kernel, such that all
spin locks in the kernel use the rqspinlock slow path. As such,
benchmarks that stress kernel spin locks end up exercising rqspinlock.
More details in the cover letter in commit 6ffb9017e932 ("Merge branch
'resilient-queued-spin-lock'")"
* tag 'bpf_res_spin_lock' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (24 commits)
selftests/bpf: Add tests for rqspinlock
bpf: Maintain FIFO property for rqspinlock unlock
bpf: Implement verifier support for rqspinlock
bpf: Introduce rqspinlock kfuncs
bpf: Convert lpm_trie.c to rqspinlock
bpf: Convert percpu_freelist.c to rqspinlock
bpf: Convert hashtab.c to rqspinlock
rqspinlock: Add locktorture support
rqspinlock: Add entry to Makefile, MAINTAINERS
rqspinlock: Add macros for rqspinlock usage
rqspinlock: Add basic support for CONFIG_PARAVIRT
rqspinlock: Add a test-and-set fallback
rqspinlock: Add deadlock detection and recovery
rqspinlock: Protect waiters in trylock fallback from stalls
rqspinlock: Protect waiters in queue from stalls
rqspinlock: Protect pending bit owners from stalls
rqspinlock: Hardcode cond_acquire loops for arm64
rqspinlock: Add support for timeouts
rqspinlock: Drop PV and virtualization support
rqspinlock: Add rqspinlock.h header
...
-----BEGIN PGP SIGNATURE-----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=aN/V
-----END PGP SIGNATURE-----
Merge tag 'bpf-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf updates from Alexei Starovoitov:
"For this merge window we're splitting BPF pull request into three for
higher visibility: main changes, res_spin_lock, try_alloc_pages.
These are the main BPF changes:
- Add DFA-based live registers analysis to improve verification of
programs with loops (Eduard Zingerman)
- Introduce load_acquire and store_release BPF instructions and add
x86, arm64 JIT support (Peilin Ye)
- Fix loop detection logic in the verifier (Eduard Zingerman)
- Drop unnecesary lock in bpf_map_inc_not_zero() (Eric Dumazet)
- Add kfunc for populating cpumask bits (Emil Tsalapatis)
- Convert various shell based tests to selftests/bpf/test_progs
format (Bastien Curutchet)
- Allow passing referenced kptrs into struct_ops callbacks (Amery
Hung)
- Add a flag to LSM bpf hook to facilitate bpf program signing
(Blaise Boscaccy)
- Track arena arguments in kfuncs (Ihor Solodrai)
- Add copy_remote_vm_str() helper for reading strings from remote VM
and bpf_copy_from_user_task_str() kfunc (Jordan Rome)
- Add support for timed may_goto instruction (Kumar Kartikeya
Dwivedi)
- Allow bpf_get_netns_cookie() int cgroup_skb programs (Mahe Tardy)
- Reduce bpf_cgrp_storage_busy false positives when accessing cgroup
local storage (Martin KaFai Lau)
- Introduce bpf_dynptr_copy() kfunc (Mykyta Yatsenko)
- Allow retrieving BTF data with BTF token (Mykyta Yatsenko)
- Add BPF kfuncs to set and get xattrs with 'security.bpf.' prefix
(Song Liu)
- Reject attaching programs to noreturn functions (Yafang Shao)
- Introduce pre-order traversal of cgroup bpf programs (Yonghong
Song)"
* tag 'bpf-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (186 commits)
selftests/bpf: Add selftests for load-acquire/store-release when register number is invalid
bpf: Fix out-of-bounds read in check_atomic_load/store()
libbpf: Add namespace for errstr making it libbpf_errstr
bpf: Add struct_ops context information to struct bpf_prog_aux
selftests/bpf: Sanitize pointer prior fclose()
selftests/bpf: Migrate test_xdp_vlan.sh into test_progs
selftests/bpf: test_xdp_vlan: Rename BPF sections
bpf: clarify a misleading verifier error message
selftests/bpf: Add selftest for attaching fexit to __noreturn functions
bpf: Reject attaching fexit/fmod_ret to __noreturn functions
bpf: Only fails the busy counter check in bpf_cgrp_storage_get if it creates storage
bpf: Make perf_event_read_output accessible in all program types.
bpftool: Using the right format specifiers
bpftool: Add -Wformat-signedness flag to detect format errors
selftests/bpf: Test freplace from user namespace
libbpf: Pass BPF token from find_prog_btf_id to BPF_BTF_GET_FD_BY_ID
bpf: Return prog btf_id without capable check
bpf: BPF token support for BPF_BTF_GET_FD_BY_ID
bpf, x86: Fix objtool warning for timed may_goto
bpf: Check map->record at the beginning of check_and_free_fields()
...
