The errno.h header is not always included indirectly, leading
to rare randconfig build warnings.
drivers/media/pci/mgb4/mgb4_regs.c:20:11: error: use of undeclared identifier 'EINVAL'
20 | return -EINVAL;
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This card has the following ICs: Hybrid tuner TDA18271, CX23888 PCIe
bridge/demodulator/decoder (and DVB-T demodulator AF9013S, which is
not within the scope of this patch). It has the following inputs: Tuner,
S-Video, Composite (shared with the luma input of S-Video) and Audio L/R
RCA. VID:PID is 1461:e139. When the patch is applied and the cx23885
kernel module is built and loaded, the following dmesg can be seen:
[ 749.677298] cx23885: cx23885 driver version 0.0.4 loaded
[ 749.677554] cx23885: CORE cx23885[0]: subsystem: 1461:e139, board: AVerMedia H789-C [card=63,autodetected]
[ 749.831841] cx25840 8-0044: cx23888 A/V decoder found @ 0x88 (cx23885[0])
[ 750.451676] cx25840 8-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
[ 750.488064] tuner: 7-0063: Tuner -1 found with type(s) Radio TV.
[ 750.488115] tda18271 7-0063: creating new instance
[ 750.490153] tda18271: TDA18271HD/C2 detected @ 7-0063
[ 750.805043] cx23885: cx23885[0]: registered device video2 [v4l2]
[ 750.805151] cx23885: cx23885[0]: registered device vbi2
[ 750.808682] cx23885: cx23885[0]: alsa: registered ALSA audio device
[ 750.808693] cx23885: cx23885_dev_checkrevision() Hardware revision = 0xd0
[ 750.808700] cx23885: cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 18, latency: 0, mmio: 0xddc00000
The card has to be defined in cx23885-cards.c (firmware also has to be
loaded) and cx23885.h. Moreover, audio routing is configured in
cx23885-video.c. Analog tuning, composite, s-video and stereo audio
inputs have been successfully tested with PAL B/G.
Signed-off-by: Plamen Atanasov <tigerment@mail.bg>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
ipu6_dma_get_sgtable() is now unused. Drop it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The bus_info in v4l2_capability of IPU6 isys v4l2_dev is missing.
The driver didn't set the dev_parent of v4l2_dev, its parent is set
to its parent auxdev which is neither platform nor PCI device, thus
media_set_bus_info() will not set the bus_info of v4l2_capability, then
`v4l2-ctl --all` cannot show the bus_info.
This patch fixes it by setting the dev_parent of video_device and v4l2
framework can detect the device type and set the bus_info instead.
Fixes: 3c1dfb5a69cf ("media: intel/ipu6: input system video nodes and buffer queues")
Cc: stable@vger.kernel.org
Signed-off-by: Hidenori Kobayashi <hidenorik@chromium.org>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The reason why this passed unnoticed is that most infotainment systems
use frequencies near enough the middle (50MHz) where both sets work.
Fixes: 0ab13674a9bd ("media: pci: mgb4: Added Digiteq Automotive MGB4 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The CMT "magic values" registers must be updated while the CMT reset
registers are active.
Fixes: 0ab13674a9bd ("media: pci: mgb4: Added Digiteq Automotive MGB4 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
netup_eeprom_write() was added in 2009 by
commit b45c0551f94d ("V4L/DVB (10797): Add EEPROM code for NetUP Dual
DVB-S2 CI card.")
but has remained unused.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
After suspend-to-memory or suspend-to-disk, additional chips are no longer
reachable via i2c. Trying to tune to DVB-C on a cx23885 based
Hauppauge WinTV-HVR-4400-HD:
si2165 8-0064: could not set chip_mode
tda18271: performing RF tracking filter calibration
This patch implements the simplest possible suspend/resume that is
enough to tune to dvb-c channel after resume.
Afterwards dmesg looks like this:
si2165 8-0064: downloading firmware from file 'dvb-demod-si2165.fw' \
size=5768
si2165 8-0064: si2165_upload_firmware: extracted patch_version=0x9a, \
block_count=0x27, crc_expected=0xcc0a
si2165 8-0064: fw load finished
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Added support for GMSL modules variants 3 and 4. Variant 3 is the same as
variant 2 from the driver's point of view. Variant 4 has "hardwired" daisy
chain loopback outputs and thus missing the v4l2 outputs.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/c725ad8d0ecac3cf6bbc532af567e56d47a6b75c.1738746904.git.namcao@linutronix.de
Call v4l2_get_link_freq() on a pad, instead of a control handler. This way
we can soon convert v4l2_get_link_freq() to be callable only on a pad and
remove the compatibility code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Naushir Patuck <naush@raspberrypi.com> # rp1-cfe
Acked-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> # st-mipid02
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Support the use of the media pad for obtaining the link frequency.
Similarly, call the v4l2_get_link_freq() on the media pad, not on the
remote's control handler.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Obtain the link frequency from the sub-device's pad instead of a control
handler. This allows obtaining it using the get_mbus_config() sub-device
pad op which is the only method supported by the IVSC driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since commit 88785982a19d ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
-----BEGIN PGP SIGNATURE-----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=ktuX
-----END PGP SIGNATURE-----
Merge tag 'media/v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Sensor driver fixes
- remove dead TI wl128x FM radio driver
- Add support for the imx462 sensor at the IMX290 binding
- V4L2 pixel data transmitter and receiver documentation improvements
- Add support for MIPI Discovery and Configuration for C-PHY line
orders
- imx8-isi fixes and improvements
- stm32: dcmipp: add core support for the stm32mp25
- qcom: camss: Add sc7280 support
- Various fixes and enhancements
* tag 'media/v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (152 commits)
media: nuvoton: Fix an error check in npcm_video_ece_init()
media: dvb-usb-v2: af9035: fix ISO C90 compilation error on af9035_i2c_master_xfer
media: platform: rzg2l-cru: rzg2l-video: Fix the comment in rzg2l_cru_start_streaming_vq()
media: fix secfeed undefined when filter alloc fail
media: dt-bindings: trivial white-space and example cleanup
MAINTAINERS: repair file entry in MEDIA DRIVERS FOR STM32 - CSI
media: solo6x10: Use const 'struct bin_attribute' callback
media: saa7164: Remove unused values
staging: media: imx: fix OF node leak in imx_media_add_of_subdevs()
media: platform: exynos4-is: Remove unused __is_get_frame_size
media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread
media: mmp: Bring back registration of the device
media: cec: include linux/debugfs.h and linux/seq_file.h where needed
Revert "media: qcom: camss: Restructure camss_link_entities"
media: venus: Remove unused hfi_core_ping()
media: dt-bindings: qcom-venus: Deprecate video-decoder and video-encoder where applicable
media: venus: Populate video encoder/decoder nodename entries
media: venus: Add support for static video encoder/decoder declarations
media: venus: match instance creation and destruction order
media: venus: destroy hfi session after m2m_ctx release
...
The sysfs core now provides callback variants that explicitly take a
const pointer. Use them so the non-const variants can be removed.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Constify the following API:
struct device *device_find_child(struct device *dev, void *data,
int (*match)(struct device *dev, void *data));
To :
struct device *device_find_child(struct device *dev, const void *data,
device_match_t match);
typedef int (*device_match_t)(struct device *dev, const void *data);
with the following reasons:
- Protect caller's match data @*data which is for comparison and lookup
and the API does not actually need to modify @*data.
- Make the API's parameters (@match)() and @data have the same type as
all of other device finding APIs (bus|class|driver)_find_device().
- All kinds of existing device match functions can be directly taken
as the API's argument, they were exported by driver core.
Constify the API and adapt for various existing usages.
BTW, various subsystem changes are squashed into this commit to meet
'git bisect' requirement, and this commit has the minimal and simplest
changes to complement squashing shortcoming, and that may bring extra
code improvement.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org> # for drivers/pwm
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-4-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACPI headers have introduced implementations for some of their
functions when the kernel is not configured with ACPI.
Let's use them instead of our conditional compilation. It is easier to
maintain and less prone to errors.
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-ipu-v5-7-3d6b35ddce7b@chromium.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It generally is not OK to use acpi_status and/or AE_ error codes
without CONFIG_ACPI and they really only should be used in
drivers/acpi/ (and not everywhere in there for that matter).
So acpi_get_physical_device_location() needs to be redefined to return
something different from acpi_status (preferably bool) in order to be
used in !CONFIG_ACPI code.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-ipu-v5-1-3d6b35ddce7b@chromium.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When ipu6 driver is waiting for the ivsc driver to probe,
which can fail or take long time, we can get plenty of ipu6
messages like this:
[ 15.454049] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.456600] intel-ipu6 0000:00:05.0: FW version: 20230925
[ 15.458292] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.461186] intel-ipu6 0000:00:05.0: FW version: 20230925
[ 15.463616] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.466490] intel-ipu6 0000:00:05.0: FW version: 20230925
Print them only when debugging is enabled to do not flood dmesg.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
cx18_reset_ir_gpio() has been unused in tree since 2009
commit eefe1010a465 ("V4L/DVB (10759): cx18: Convert GPIO connected
functions to act as v4l2_subdevices")
It has a comment saying it's exported for use by 'lirc_pvr150' but I don't
see any sign of it in the lirc git, and I see it removed support
for lirc_i2c.c 'Flavors of the Hauppage PVR-150...' in 2014.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Do not define stuff used in a single source file in a global header.
Do not mix defines with "bare" values in the initialization.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Unify the names of HW hsync/vsync registers between the inputs and outputs.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Write the padding to the HW registers at the same place as the input logic
does.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
flexcop_dma_control_size_irq() last use was removed in 2005 by
commit 64221be7b900 ("[PATCH] dvb: flexcop: woraround irq stop problem")
flexcop_dump_reg() last use was removed in 2009 by
commit 382c5546d618 ("V4L/DVB (10694): [PATCH] software IRQ watchdog for
Flexcop B2C2 DVB PCI cards")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAmc8Q80ACgkQCF8+vY7k
4RX+3g//dMBSmu3uC9OiXyfw3aB8w62RMeieRxSVPMdkiacUm1J8HyzHnXPXIUn3
tfBT9E/YbeFZ+PlrOXRDUi1i8jmN47VuwRe01rxxF/FdlYknC2eGH3Ug9DW90VBh
wmZ1kSjyjizwDkKAm+Jc2xynTaX+iInJ4Kzp9RStDZPuaqj2Qzd1qVRk2FJwAYRh
5dTpi0W1PexjxQXDIcnHi/tPapGLSP5PnrunrAJR0tYfp60wrKMaxTO36yJzbnDP
MxkF8A+9dWtePRqoPWxPIvnOVu/+Twc730xkQp62qPvwEM2HZRtU7cgQFlWos6p/
ijK2i6sAQslMhQ9oIyKlO7HpXX60rjE3XtdzEtGxBq6DyIqx1riN+OqJB2C4Cdsr
2qUET8aTIisPURw1ecNAbthvLt8tljBe08/eX0GYaWFjALJx3Pds23ahH8hw295N
o3SY5NaGmO9Tg6HzYLSwfBmxgGpWDuRic6PDCVKok5mS5D1+uV/tu8fQFiNiFNVe
Okufjvo7HtZ3+rWR90b/Udpz/lBB/dceppnUX2iKevrG190VHxEwJ2pQKkfdH9ha
LUZQajikiv5rbGxKIGrjrCnjrJ24TC2vCSPhkgOb1r91LUY4RUV61c3hZbH73rzQ
2Ykwvmy+gpE4GEYiJRfSR6KlXdBruMa5FToLUHEK0uBMSlG5k7Q=
=25BS
-----END PGP SIGNATURE-----
Merge tag 'media/v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- removal of the old omap4iss media driver
- mantis: remove orphan mantis_core.h
- add support for Raspberypi CFE
- uvc driver got a co-maintainer
- main media tree moved to git://linuxtv.org/media.git
- lots of driver cleanups, updates and fixes
* tag 'media/v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (233 commits)
docs: media: update location of the media patches
MAINTAINERS: update location of media main tree
media: MAINTAINERS: Add Hans de Goede as USB VIDEO CLASS co-maintainer
media: platform: samsung: s5p-jpeg: Remove deadcode
media: qcom: camss: Add MSM8953 resources
media: dt-bindings: Add qcom,msm8953-camss
media: qcom: camss: implement pm domain ops for VFE v4.1
media: platform: exynos4-is: Fix an OF node reference leak in fimc_md_is_isp_available
media: adv7180: Also check for "adi,force-bt656-4"
media: dt-bindings: adv7180: Document 'adi,force-bt656-4'
media: mgb4: Fix inconsistent input/output alignment in loopback mode
media: replace obsolete hans.verkuil@cisco.com alias
Documentation: media: improve V4L2_CID_MIN_BUFFERS_FOR_*, doc
media: vicodec: add V4L2_CID_MIN_BUFFERS_FOR_* controls
media: atomisp: Add check for rgby_data memory allocation failure
media: atomisp: remove redundant re-checking of err
media: atomisp: Fix spelling errors reported by codespell
media: atomisp: Remove License information boilerplate
media: atomisp: Fix typos in comment
media: atomisp: hmm_bo: Fix spelling errors in hmm_bo.h
...
The only real core work we've got this time around is the completion of
the transition to the new host/target naming for the core APIs, Kconfig
still needs doing but that's a lot less invasive. Otherwise the big
changes are the new drivers that have been added:
- Completion of the conversion to spi_alloc_host()/_target() and
removal of the old naming.
- Cleanups for Rockchip drivers, these brought in a new logging helper
in the driver core for warnings during probe.
- Support for configuration of the word delay via spidev_test.
- Support for AMD HID2 controllers, Apple SPI controller and Realtek
SPI-NAND controllers.
The Rockchip cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmc7QdQACgkQJNaLcl1U
h9A7KAf+Od8ORLheHKrokFYWEW1zuiR45EjqWylLk835d3TQn/VfLOouRDhOPKLw
wmxy5PjjvI+CHa9JY4TXY6iRTCc8By6fkwRWFZN5KApSC2NQriWiqgTSItFfYiLv
yUthZjfRhbfSpf6E/0hq4axpfn+6W/MIWUg7Ag08IEU+GhDd+um8gdpBKsP1BAJF
s34Fn3oJNoze0Wwcq5tZ91S1MsP+2vGFGIGC2HA7G2GAXjGFqBZUnIL+zjC1US3j
XILAoy4Vx4J0Nn+f+zdGL2m5cm6O49ztaKqUxamVFigwM4va5OSOEpcnFMEPZ8HY
013dIg7tiayUTOTcByCpzfMDWuzHig==
=jc6e
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The only real core work we've got this time around is the completion
of the transition to the new host/target naming for the core APIs,
Kconfig still needs doing but that's a lot less invasive.
Otherwise the big changes are the new drivers that have been added:
- Completion of the conversion to spi_alloc_host()/_target() and
removal of the old naming.
- Cleanups for Rockchip drivers, these brought in a new logging
helper in the driver core for warnings during probe.
- Support for configuration of the word delay via spidev_test.
- Support for AMD HID2 controllers, Apple SPI controller and Realtek
SPI-NAND controllers"
* tag 'spi-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (58 commits)
spi: imx: support word delay
spi: imx: pass struct spi_transfer to prepare_transfer()
spi: cs42l43: Add GPIO speaker id support to the bridge configuration
spi: Delete useless checks
spi: apple: Remove unnecessary .owner for apple_spi_driver
spi: spidev_test: add support for word delay
spi: apple: Add driver for Apple SPI controller
spi: dt-bindings: apple,spi: Add binding for Apple SPI controllers
spi: Use of_property_present() for non-boolean properties
spi: zynqmp-gqspi: Undo runtime PM changes at driver exit time
spi: spi-mem: rtl-snand: Correctly handle DMA transfers
spi: tegra210-quad: Avoid shift-out-of-bounds
spi: axi-spi-engine: Emit trace events for spi transfers
dt-bindings: spi: sprd,sc9860-spi: convert to YAML
spi: Replace deprecated PCI functions
spi: dt-bindings: samsung: Add a compatible for samsung,exynos8895-spi
spi: spi-mem: Add Realtek SPI-NAND controller
dt-bindings: spi: Add realtek,rtl9301-snand
spi: make class structs const
spi: dt-bindings: brcm,bcm2835-aux-spi: Convert to dtschema
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmcxMXceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1IgH/A3O7KIy/VR7D7O3
usbLqk1V+YWs/NsVdewEL/SYfXjCxqnejdk/AvN3ZAIxFeMHhAmcSCKno3zKgK9L
ML4kDrz22dPlA0XncNM8qKTCqAMgXTur1wafv3NAjutg0D3eHvAp0BW0GO5px93G
+kt3kOY32UaB+2Fl1GIub777pRi5U4u5AboQTu3x0TdRZJtV1pqgeddGoymNn6mi
xmMVbY3r5MXJQyHntoT9FIuxK3d+jGcgRHP5RWr53+vAUEFdlXiGcJV4dUXsuQNa
sEKJutCaUqQeiamjoo4bRZO7/2OAPX9Sv7sNIXD/irZZJmCcWr+GDCcUmL69Mjg7
7mx6XrM=
=HYUx
-----END PGP SIGNATURE-----
Merge tag 'v6.12-rc7' into __tmp-hansg-linux-tags_media_atomisp_6_13_1
Linux 6.12-rc7
* tag 'v6.12-rc7': (1909 commits)
Linux 6.12-rc7
filemap: Fix bounds checking in filemap_read()
i2c: designware: do not hold SCL low when I2C_DYNAMIC_TAR_UPDATE is not set
mailmap: add entry for Thorsten Blum
ocfs2: remove entry once instead of null-ptr-dereference in ocfs2_xa_remove()
signal: restore the override_rlimit logic
fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
ucounts: fix counter leak in inc_rlimit_get_ucounts()
selftests: hugetlb_dio: check for initial conditions to skip in the start
mm: fix docs for the kernel parameter ``thp_anon=``
mm/damon/core: avoid overflow in damon_feed_loop_next_input()
mm/damon/core: handle zero schemes apply interval
mm/damon/core: handle zero {aggregation,ops_update} intervals
mm/mlock: set the correct prev on failure
objpool: fix to make percpu slot allocation more robust
mm/page_alloc: keep track of free highatomic
bcachefs: Fix UAF in __promote_alloc() error path
bcachefs: Change OPT_STR max to be 1 less than the size of choices array
bcachefs: btree_cache.freeable list fixes
bcachefs: check the invalid parameter for perf test
...
-----BEGIN PGP SIGNATURE-----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=SGfF
-----END PGP SIGNATURE-----
Merge tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-core fixes for vb2 check and device registration
- v4l2-core: fix an issue with error handling for VIDIOC_G_CTRL
- vb2 core: fix an issue with vb plane copy logic
- videobuf2-core: copy vb planes unconditionally
- vivid: fix buffer overwrite when using > 32 buffers
- vivid: fix a potential division by zero due to an issue at v4l2-tpg
- some spectre vulnerability fixes
- several OOM access fixes
- some buffer overflow fixes
* tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videobuf2-core: copy vb planes unconditionally
media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
media: vivid: fix buffer overwrite when using > 32 buffers
media: pulse8-cec: fix data timestamp at pulse8_setup()
media: cec: extron-da-hd-4k-plus: don't use -1 as an error code
media: stb0899_algo: initialize cfr before using it
media: adv7604: prevent underflow condition when reporting colorspace
media: cx24116: prevent overflows on SNR calculus
media: ar0521: don't overflow when checking PLL values
media: s5p-jpeg: prevent buffer overflows
media: av7110: fix a spectre vulnerability
media: mgb4: protect driver against spectre
media: dvb_frontend: don't play tricks with underflow values
media: dvbdev: prevent the risk of out of memory access
media: v4l2-tpg: prevent the risk of a division by zero
media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
media: dvb-core: add missing buffer index check
Fixes broken output due to different input/output alignment in loopback
mode when the (last) input device is closed. Instead of on device close,
do the alignment synchronisation when starting the stream (and clear
it when streaming is stopped).
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The old hans.verkuil@cisco.com email address was discontinued years ago.
Replace it with the correct hansverk@cisco.com email.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The DMA unmap API is not supposed to return value. Thus this patch
changes the ipu6_mmu_unmap() as a void function and DMA unmapping
didn't check the return value.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
[Sakari Ailus: Drop unnecessary returns.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The MMU mapping flow is optimized for improve the performance, the
unmapping flow could also be optimized to follow same flow.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
ipu6_mmu_map() operated on a per-page basis, it leads frequent
spin_lock/unlock() and clflush_cache_range() for each page, it
will cause inefficiencies especially when handling dma-bufs
with large number of pages. However, the pages are likely concentrated
pages by IOMMU DMA driver, IPU MMU driver can map the concentrated
pages into less entries in l1 table.
This change enhances ipu6_mmu_map() with batching process multiple
contiguous pages. It significantly reduces calls for spin_lock/unlock
and clflush_cache_range() and improve the performance.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Jianhui Dai <jianhui.j.dai@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
l2_map() and l2_unmap() are better to be grouped together.
l2_unmap() will soon be called from l2_map() for mapping
optimization.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Jianhui Dai <jianhui.j.dai@intel.com>
[Sakari Ailus: Rebase on debug print fixes on 32-bit.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The buttress ipc ish structure is not effectively used on IPU6 - data
is nullified on init. Remove the ish structure and handing of related
interrupts to cleanup the code.
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Some IPU6 devices have shared interrupts. We need to handle properly
case when interrupt is triggered from other device on shared irq line
and IPU6 itself disabled. In such case we get 0xffffffff from
ISR_STATUS register and handle all irq's cases, for what we are not
not prepared and usually hang the whole system.
To avoid the issue use pm_runtime_get_if_active() to check if
the device is enabled and prevent suspending it when we handle irq
until the end of irq. Additionally use synchronize_irq() in suspend
Fixes: ab29a2478e70 ("media: intel/ipu6: add IPU6 buttress interface driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Use PFN_UP() and sg_virt() can be used to simplify the code.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
IPU6 driver doesn't override the dma_ops of device now, it doesn't
depends on the ARCH_HAS_DMA_OPS, so remove the dependency in Kconfig.
Fixes: de6c85bf918e ("dma-mapping: clearly mark DMA ops as an architecture feature")
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
dma_ops is removed from the IPU6 auxiliary device, ISYS driver
should use the IPU6 DMA mapping APIs directly instead of depending
on the device callbacks.
ISYS driver switch from the videobuf2 DMA contig memory allocator to
scatter/gather memory allocator.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
[Sakari Ailus: Rebased on recent videobuf2 wait changes.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
DMA ops are a helper for architectures and not for drivers to override the
DMA implementation. Driver should not override the DMA implementation.
This patch removes the dma_ops override from auxiliary device and adds
driver-internal helpers that use the actual DMA mapping APIs.
Fixes: 9163d83573e4 ("media: intel/ipu6: add IPU6 DMA mapping API and MMU table")
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[Sakari Ailus: Fix the commit message a little.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Fix printing DMA and physical address printing on 32-bit platforms, by
using correct types. Also cast DMA_BIT_MASK() result to dma_addr_t to make
Clang happy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This file has been an orphan ever since commit b3b961448f70
("V4L/DVB (13795): [Mantis/Hopper] Code overhaul, add Hopper
devices into the PCI ID list"), having no references except
for the orphan removed by commit 519648bed470 ("media: mantis:
remove orphan mantis_core.c")
Fixes: b3b961448f70 ("V4L/DVB (13795): [Mantis/Hopper] Code overhaul, add Hopper devices into the PCI ID list")
Link: https://patchwork.linuxtv.org/project/linux-media/patch/1277054487-14384-1-git-send-email-bjorn@mork.no/
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since commit 88785982a19d ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Frequency range is set from sysfs via frequency_range_store(),
being vulnerable to spectre, as reported by smatch:
drivers/media/pci/mgb4/mgb4_cmt.c:231 mgb4_cmt_set_vin_freq_range() warn: potential spectre issue 'cmt_vals_in' [r]
drivers/media/pci/mgb4/mgb4_cmt.c:238 mgb4_cmt_set_vin_freq_range() warn: possible spectre second half. 'reg_set'
Fix it.
Fixes: 0ab13674a9bd ("media: pci: mgb4: Added Digiteq Automotive MGB4 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
